久久久久久久精品成人热小说,亚洲 欧美 激情 小说 另类,亚洲精品国产精华液,激烈 痉挛 抽搐 潮喷 MP4

News

Common faults and solutions of dispensing valves

Release Date:2017-07-30
Common faults and solutions of dispensing valves

1. Dripping occurs after the dispensing valve is closed.

This situation is mostly caused by the small caliber of the needle used. A needle that is too small can affect the flow of liquid and cause back pressure, resulting in dripping shortly after the rubber valve is closed. A too small needle can also affect the exhaust bubble action of the rubber valve when it is first used, and this problem can be solved by replacing it with a larger needle.
2. Inconsistent adhesive size.
When the dispensing is inconsistent, it is mainly due to the unstable pressure of the pressure cylinder or air storing the fluid. The intake pressure regulator should be set at a pressure 10 to 15 psi lower than the minimum pressure in the factory. The pressure used by the pressure cylinder should be above the middle pressure of the regulator, and it should be avoided to use a pressure between the low pressure part of the pressure gauge. The control pressure of the glue valve should be at least 60psi to ensure stable glue dispensing. Finally, the glue dispensing time should be checked. If it is less than 15/1000 seconds, it will cause unstable glue dispensing. The longer the glue dispensing time, the more stable the glue dispensing.
3. The flow rate is too slow.
If the flow rate is too slow, the pipeline should be changed from 1/4 "to 3/8". If there is no need, the pipeline should be as short as possible.
4. Bubbles inside the fluid.
If the fluid pressure is too high and the valve opening time is too short, air may seep into the liquid. The solution is to reduce the fluid pressure and use a conical inclined needle.
5. Instant glue (quick drying glue) blocks the glue valve joint and pipeline.
This situation is mainly due to excessive moisture or repeated use of instant glue. It should be ensured to use fresh instant glue, thoroughly clean the pipeline with acetone that does not contain moisture, and ensure that the air used is completely dry. A filter should be installed between the air pressure and the glue valve system in the factory. If the above methods are still ineffective, nitrogen should be used
展開
日产乱码一二三区别视频| 亚洲AV无码乱码在线观看,不卡| 连开两个处苞过程| 99久久免费国产精品| 欧美大成色WWW永久网站婷| 日本三级吃奶头添泬播放| 国产成人无码一区二区在线播放| 奇米777四色欧美在线视频| 人妻少妇精品视频一区二区三区| 久碰人妻人妻人妻人妻人掠| 97亚洲成a人无码亚洲成a无码| 欧美视频毛片在线播放| 囯产免费一区二区三区 | 久久久久久国产精品无码下载| 野花日本hd免费高清版7| 宝宝好涨水快流出来免费视频| 午夜福利麻豆国产精品| 扒开粉嫩细缝喷白浆sex| 野花日本韩国免费视频6| 久久8精品亚洲AV无码| 久久精品国产亚洲AV麻豆| 久久婷婷五月综合国产尤物APP| 无码日本精品xxxxxxxxx| 亚洲 成人 综合 另类 图区| 艳妇荡岳丰满交换做爰| 日本VA欧美VA欧美VA精品| 国产乱人伦AV在线A麻豆| 性久久久久久久| 欧美大荫蒂毛茸茸视频| 裙底下的男友1v1校园高h| 国产午夜三级一区二区三| 国产农村妇女毛片精品久久| 亚洲人成无码网站久久99热国产 | 真人性囗交69视频| 中文字幕人妻无码乱精品 | 噜噜狠狠色综合久色a站网址| 福利cosplayh裸体の福利| 久久精品国产亚洲AV日韩| 亚洲精品无码人妻无码| 欧美日韩国产精品自在自线| 好爽~好硬~好紧~还要|